System Integration
Different systems, one mind.
Let your systems know each other and act together
Hardware and Software Layers that Make Up the System
Each component works with a certified, redundant and central integration infrastructure at international standards.
Security Information Management
CCTV, access control, fire and perimeter security alarms are combined on a single platform. Incidents are displayed on the map, the operator is presented with step-by-step intervention procedures and the entire process is recorded.
- PSIM (Physical Security Information Management) software infrastructure
- Instant alarm placement on geographic information system (GIS) and 3D building floor plan
- Intervention steps guiding the operator with standard operating procedures (SOP)
- Event correlation with single time synchronization of all safety sensors
Subsystem Integration with building management system
HVAC, lighting, energy, elevator and other technical systems are connected to the building management system. The entire building is monitored and managed from a single interface.
- Central monitoring of mechanical boiler rooms, chillers and air handling units
- Elevator floor control, generator and transformer data transfer to BMS
- Scenarios of fire and smoke dampers matching mechanical ventilation
- Graphically animated flowcharts for plant technicians
Fire – Transition – Announcement Scenario Integration
When a fire is detected, automatic scenarios enable the doors to be opened, the evacuation announcement begins, the elevators descend to the safe floor and the smoke control is activated. Human error is minimized and evacuation time is shortened.
- Hardware relay and IP based double safety emergency scenario bridge
- Release of magnetic locks and emergency opening position of turnstiles
- Automatic start of EN 54 voice alarm broadcast with evacuation zone priority
- Synchronized activation of fire doors and smoke exhaust dampers
Hotel Systems Integration
Hotel management software, room management system, IPTV and card lock systems work together. With the check-in process, the room becomes ready, the TV welcomes the guest, and with the check-out process, energy saving mode is switched.
- Seamless integration of PMS (Opera, Fidelio etc.) with GRMS, IPTV and door locks
- Bringing the room to comfort temperature and a welcome scenario upon check-in
- With the guest card, the elevator goes only to the floor where the guest stays.
- Resetting the TV at check-out and putting the room into energy saving mode
Control and Monitoring Center Setup
Central monitoring rooms with video wall, operator consoles, software and ergonomic design are installed on a turnkey basis. Security and operations are managed centrally 24/7.
- Ergonomic modular operator consoles suitable for 24/7 uninterrupted operation
- Managing dozens of servers via a single keyboard-mouse with multiple KVM switching
- Acoustic insulation, anti-static raised floor and technical lighting
- Redundant air conditioning (precision controlled) and uninterrupted UPS infrastructure
Open Protocol Integrations
Devices of different brands and technologies are connected to each other through open communication protocols. A brand-independent, flexible and future-proof system architecture is created.
- BACnet IP/MSTP, Modbus RTU/TCP industrial communication protocols
- KNX building automation and DALI-2 lighting buses
- ONVIF Profile S/G/T and OPC UA industrial data integration standards
- Gateways that translate data between different protocols with zero loss
Combining Multi-Brand Systems on a Single Platform
Systems from different manufacturers are managed from a single interface. Existing investments are protected; An integrated structure is established without being dependent on a single brand.
- Protecting and integrating pre-installed cameras and panels in the field
- Architecture that completely prevents lock-in to a single vendor (Vendor Lock-in)
- Upgrade legacy analog or proprietary protocols to modern IP standards
- Phased modernization that maximizes return on investment (ROI)
Advantages of System Integration
System Integration Its investment directly reduces operational costs while increasing infrastructure security and efficiency.
Rapid Response
Events are seen on one screen; Intervention steps are directed automatically.
Less Human Error
Critical scenarios run automatically without requiring manual action.
Independence from Brand
Systems from different manufacturers are managed together in a single interface.
Protected Investment
Existing systems are included in the new structure without being renewed.
Why FAV Technology?
Not a product vendor, but a turnkey integration and sustainability partner.
Reliable Brands, Right Choice
We select the products of world brands such as Genetec, Milestone and Honeywell according to the needs and budget of your project; We establish systems that are brand independent and open to the future.
- Genetec Unified Security and Milestone XProtect corporate partnership
- Honeywell EBI and building management integration experience
- More than 1,000 brands and hardware support with open architecture platforms
Frequently Asked Questions
System Integration Questions about infrastructure, standards and corporate application processes.
Applied Sectors
Multi-layered protection and command-control in high security facilities.
Detailed Information
Security, announcement and control center integration in heavy passenger flow.
Detailed Information
Elevate guest experience and operation on the same infrastructure.
Detailed Information
Physical and digital protection for uninterrupted service.
Detailed InformationSolutions Included in This System
Systems do not stand alone; It works together on the axes of operational needs.
Frequently Preferred Together
System Integration Systems that work fully integrated with and are preferred together in projects.
Let's plan a survey for your project
Let our expert team examine your existing systems and design the integration architecture and automatic scenarios according to your needs.